Key points
- A house with a basement always starts with a soil investigation and groundwater data.
- An empty basement or pool can be lifted by groundwater pressure if it is not heavy enough.
- A basement used as living space must stay dry, so the waterproofing strategy must be designed from the start.
- A pool on a suspended slab adds heavy load: each metre of water depth adds roughly one tonne per square metre.

A house with a basement and a pool gains valuable space, especially on tight urban plots. But both sit below ground or hold water, so small design mistakes can lead to leaks, cracks or costly repairs. Here are the structural and foundation points worth discussing with your engineer at concept stage.
Start with a soil investigation
Before fixing the basement depth, you need to know the soil type and groundwater level on site. This comes from a soil investigation, such as CPT and boreholes with SPT. We explain the difference in CPT vs SPT.
What the investigation should give you:
- Soil layers and bearing capacity below the basement floor.
- The groundwater level, including how high it may rise in the rainy season.
- Risks to neighbouring houses during excavation and dewatering.
- Parameters for designing the retaining walls.
Tip: One test point is rarely enough for a large or sloping plot. Agree the number and depth of test points with a geotechnical engineer rather than just following a minimum.
Choosing foundations for a house with a basement
No single foundation type is always right for a house with a basement. The choice depends on the soil, the loads and the surroundings. Residential projects designed by Stadin show the variety:
| Project | Key data | Foundation |
|---|---|---|
| Residence in Menteng | 3 storeys, 1 basement, 2011 | Shallow foundation |
| Residence at Royal Golf Karawaci | 2 storeys, 1,037 m² plus pool, 1 basement, 2010 | Driven piles |
| High-End Residence in Citraland | 2,100 m² site, 3,000 m² building, 2 storeys, 1 basement, 2021 | Based on site soil data |
The Menteng house uses shallow foundations despite its basement, while the Karawaci house uses driven piles. Differences like this come from soil data and loads, not preference, so never copy a neighbour's foundation without calculations.
Groundwater uplift: an often forgotten risk
A basement below the water table behaves like a boat: water pushes up on the floor slab. If the weight of the building and permanent loads above is less than that pressure, the basement can lift, the slab can crack, or water can enter through joints.
The risk is highest when the structure is still light, for example when construction has only reached the basement slab, or when the pool is drained. A pool emptied while the water table is high can lift because the water inside no longer adds weight.
The uplift check compares upward water pressure with the permanent loads that resist it, with safety factors. If it fails, options include:
- Thickening the base slab, or extending it beyond the walls so the soil above helps hold it down.
- Using tension piles or anchors.
- Managing drainage and lowering groundwater during construction.
Our article on basements in soft soil covers this in more detail.
Basement waterproofing that matches the use
House basements are often used for family rooms, home cinemas or bedrooms, not just parking. The widely used British Standard BS 8102 sets protection grades by use: car parking can tolerate some damp, while living space must be dry with no water penetration.
BS 8102 also describes three approaches:
- Type A (barrier): a continuous waterproof membrane around the structure.
- Type B (structurally integral): the reinforced concrete itself is designed as a watertight box, with crack width limits.
- Type C (drained cavity): an inner cavity collects seepage, which is then pumped out.
For a habitable basement, these need to be designed together with the architect and a waterproofing specialist. Common weak points are construction joints, pipe penetrations and wall-to-slab junctions.
Drainage around the house matters too. Gutters, drains and garden levels that send rainwater away from the basement walls reduce the load on the waterproofing. Also provide a sump pit at the lowest point of the basement as a back-up for seepage or water entering from outside, for example via a ramp or openings during heavy rain, and keep the pump easy to reach for maintenance.
Pools on suspended slabs
A pool on an upper floor, the roof or above the basement looks great, but it is heavy. One metre of water depth adds about 10 kN/m², roughly one tonne per square metre, before counting the pool concrete, finishes and swimmers.
Points to watch:
- Slabs, beams and columns under the pool must be designed for this load.
- Slab deflection must be small so tiles and waterproofing do not crack.
- The connection between the pool and the house structure needs thought, including possible movement joints.
- Plan maintenance access for pipes and filter equipment.
Adding a pool to an existing house is a major load change. Have the structure checked first, just as you would before adding a floor.
Conclusion
A house with a basement and pool can be safe and comfortable when the soil is properly investigated, foundations follow the data, uplift is checked at every stage, and waterproofing matches the room use. Every member size, slab thickness and foundation type must be calculated by a competent engineer for your site. To get started, talk to Stadin about soil investigation and foundation design.
This article provides general information. Every project still needs to be analysed and calculated by a competent structural or geotechnical engineer, in line with the applicable SNI codes and regulations.
Sources
- Waterproofing of Basements – Structville
- Uplift Verification for Underground Structures – Structville
- Data proyek: company profile PT. Stadin Strukturindo Konsultan (2026)


